halos on 97 camaro

Curt705 · **Posted:** Wed Jul 14, 2010 2:15 am

okay sooo i got new angle eyes for my camaro and, well i got the headlights hooked up (they were easy) but once i came with the actual halos, to me theres sooo much wiring, and i dont know where i can splice once set for the others! and i dont even know where i can get my wires threw so i can hook my switch to the dash.
sooo does anyone want to help me with my pain in the blond head delema? :ahhhh

KennyT · **Joined:** Sat Apr 03, 2010 11:47 pm **Posts:** 110

Engrish would be easier to read.

Follow the diagram, everything will be labeled most likely.

Curt705 · **Posted:** Wed Jul 14, 2010 6:38 pm

well even following the diagram doesnt really help much. i gotta wire 2 sets of them and im not sure if i have to use both wiring harnesses or if i can just splice one set to one wiring harness.

AudimanAdam · **Posted:** Wed Jul 14, 2010 10:50 pm

The halos should be just power and ground. Ground should be super easy to grab. If you want the halo's to come on with the parking lights as most do, splice each into the corresponding parking light....

Curt705 · **Posted:** Sun Jul 18, 2010 2:49 am

yeah but im trying to wire them so that i can turn them on and off as i please. having the blue halos on all the time might get me pulled over. because im not sure if they are 100% legal.

the trouble im now having is getting my wire threw my firewall and to ANYWHERE in my dash. i cant find a place where i can feed wiring threw.

the wires should easily be connected, its just the firewall thing thats giving me a whole lot of trouble.

khoist · **Posted:** Sun Jul 18, 2010 10:24 am

drill a hole

and while you're at it run your amp wire through there too, cause a car like that's gotta have the bumps

Curt705 · **Posted:** Sun Jul 18, 2010 5:02 pm

khoist wrote:

drill a hole

and while you're at it run your amp wire through there too, cause a car like that's gotta have the bumps

well i cant even get a drill in, theres no room. and my car can bump just fine if i wanted it to so HA!

Fryphax · **Joined:** Fri Oct 21, 2005 4:51 pm **Posts:** 769

Curt705 wrote:

khoist wrote:

drill a hole

and while you're at it run your amp wire through there too, cause a car like that's gotta have the bumps

well i cant even get a drill in, theres no room. and my car can bump just fine if i wanted it to so HA!

I find this hard to believe, what Kevin says is truth.

daniel_depetro · **Posted:** Mon Jul 19, 2010 9:29 am

Hey punk, your ceramic coated headers are on. :wrench

now come and get this pile. :ninja

Curt705 · **Posted:** Wed Jul 21, 2010 6:06 pm

Fryphax wrote:

Curt705 wrote:

khoist wrote:

drill a hole

and while you're at it run your amp wire through there too, cause a car like that's gotta have the bumps

well i cant even get a drill in, theres no room. and my car can bump just fine if i wanted it to so HA!

I find this hard to believe, what Kevin says is truth.

take a look at my engine area, theres hardley any room in the back.

Curt705 · **Posted:** Wed Jul 21, 2010 6:15 pm

daniel_depetro wrote:

Hey punk, your ceramic coated headers are on. :wrench

now come and get this pile. :ninja

well im glad i finally have them on, now to deal with the leak from the ERG pipe from the header. =/
it sucks but i found out thats its a common problem, so it shouldnt be too hard of a fix there.
since its on an angle one guy form the camaro forums did a high temp copper gasket sealer or just heat the pipe and bend it so the connection is right.

Northern Michigan University Car Club

halos on 97 camaro

Who is online